How would a reincarnation of a Lotus Seven with a rotary engine grab you? Adjust the pedals, insert your earplugs and turn the key of a Rotus Seven Rotary…
The Department of Commerce will, if you ask it to, provide daunting statistics on the failure rate of new businesses. If it kept such records on new automobile manufacturers (which likely it does), the numbers could only be worse: Malcolm Tucker DeLorean goes in only undercapitalized and more often than not, goes out wholly under. We’ve all seen, too, the prototype that was grandly introduced and followed up with… Nothing.
So it’s a pleasant surprise to see tiny Rotus, Ltd., still making cars nearly three years after we first looked in on the Hagerstown, Maryland concern, and not just because owner Christopher Custer is such a nice guy, which he seems to be, but also because he makes a satisfactory product. For the uninitiated, the Rotus Seven is an evolution of the original Lotus Seven concept, borrowing the idea of a bare essentials sports car and adding to it a dose of modern engineering and contemporary Japanese powerplant. (It’s, the name, a Charlie Channish interpretation of “Lotus”.) The Rotus Seven tube frame is built on a chassis plate originally designed for the construction of replacement Lotus Seven frames (sort of like lifting up a serial number and sliding a new car under it), but which has been almost completely revised. The Rotus Seven has ’80s formula-car design in its cantilevered front suspension with rocker arm upper links and inboard mounted coil-over shocks.
Review/driving impressions originally published in AutoWeek January 26, 1987; republished by author John Matras.
The Rotus Seven also makes extensive use of Toyota parts, chosen for reasons of availability, durability, cost–and because Custer owns a Toyota dealership. For example, the rear axle is a Toyota piece and the engine intended for broadest application is a Corolla “T” series, the venerable pushrod motivator of a million econoboxes.
Other engine choices have also been anticipated. The DOHC Toyota four is a perfect fit, but even larger quarry has been allowed for. Unlike a Lotus Seven, a Rotus Seven engine compartment can accommodate a small V-8 or the unusual proportions of a Mazda rotary engine. Having experienced the liveliness of a Rotus Seven powered by a mildly modified 1600 cc Toyota engine (at about 1200 pounds a couple of tightly wound rubber bands will give good performance), we jumped at the chance to test a rotary-equipped Rotus Seven.
The car we drove had a late-model Mazda 13B rotary, from a Mazda RX-7, under its aluminum hood. It was the first Rotus Seven to be Wankel equipped. Since then another car, with a 12A (an earlier RX-7 powerplant), has been built, and Custer says his firm is still learning to cope with the little wonders. One problem is the width of the Wankel, especially with Weber carbs mounted. To get the engine under the hood requires a special intake manifold that lays the carburetor back over the top of the engine (an item from Racing Beat, an Anaheim, California, maker of aftermarket Mazda high-performance equipment). A more difficult problem is dealing with the rotary’s loud and peculiar exhaust note. There’s not room under the car for the rotary’s normal exhaust, so the Rotus Seven has a tubular unit along the side of the car and a second conventional muffler in what used to be the bottom half of the trunk. The result is a fairly quiet exhaust, but the sound, a sort of model-airplane-on-steroids note, is unpleasant.
Like Chapman’s original, the Rotus Seven has a fixed seat and adjustable pedals. These are very good, perfectly spaced for heel and toeing, but adjustment requires on bolting the unit and moving it forward or back.
What this Rotus Seven Seven was intended for is good old-fashioned sports car fun and that’s something that escapes quantitative analysis. But what’s quantifiable is as follows: the ability to pull an honest 1.0 G on a skidpad on street tires without special preparation or alignment tricks. Acceleration depends on your choice of engine, but sub- 6.0sec 0-60 times are possible with the 13B rotary. With a hot Buick/Rover aluminum V-8 installed (a car with such description was in progress when we visited), that time could be appreciably lowered.
If those numbers make a Rotus Seven sound irresistible, some caveats: first a Rotus Seven is a kit car. Lest Rotus, Ltd., be classified as a manufacturer, with all the attendant legal headaches of that classification, buyers must perform at least some minor construction. Or major construction; it can be purchased as a kit. (In either form, Custer claims no registration problems in any state.) Prices for (mostly) completed cars range from $17,400 with a 1600cc Toyota to $22,500 equipped with a V-8.
What Rotus – the company – proves is that it is possible to make it in the car manufacturing business by thinking small. Very small. A month with two sales is a good month. And perhaps a very good month for two Rotus Seven customers.







